Brass Plates


We are one of the pioneer exporting houses and supplier of Brass Sheets Plates, which are all prone to sigma phase formation if exposed for long periods to a temperature of about 590 Degree C to 870 Degree C. The problem of grain boundary carbide precipitation in Brass Plates was discussed under inter – granular corrosion. The formation of sigma phase in Brass Plates is dependent on both time and temperature and is different for each type of steel. In general, Brass Coils is practically immune to sigma phase formation, but not so those grades with higher chromium contents with molybdenum or with higher silicon contents. Sigma phase embrittlement refers to the formation of a precipitate in the micro structure of Brass Slatting Coils over a long period of time within this particular temperature range.

Brass Sheet, Plate & Coil Specifications
Specifications : ASTM / ASME SB 62
Size : 1000 mm x 2000 mm, 1220 mm x 2440 mm, 1500 mm x 3000 mm, 2000 mm x 2000 mm, 2000 mm x 4000 mm
Thickness : 0.1mm to 100 mm Thk
Form : Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Strip, Flats
Finish : Hot rolled plate (HR), Cold rolled sheet (CR), 2B, No.3, No.4, HL, BA, 8K
Hardness : Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc.

 

 

Types of Brass Plates

Brass Polished Plates Polished Brass Plates
Brass UNS C36000 Polished Plates
ASTM / ASME SB62 Brass Polished Plates
Brass Hot Rolled Plates Brass Hot Rolled Plates
Carpenter Brass Hot Rolled Plates
Brass UNS C36000 Hot Rolled Plates
ASME SB62 Brass Hot Rolled Plates
Brass Cold Rolled Plates Brass Cold Rolled Plates
Brass UNS C36000 Cold Rolled Plates
ASTM / ASME SB62 Brass Cold Rolled Plates

Brass Plate Chemical Composition

Brass Cu Fe Pb Zn
Min./Max. 60.0-63.0 0.35 2.5-3.0 Rem.
Nominal 61.5 2.7 35.4

Brass Plate Physical Properties

Properties US Customary
Melting Point -Liquidus 1650 F
Melting Point -Solidus 1630 F
Density 0.307 lb/in3at 68 F
Electrical Resistivity 39.90 ohms – cmil/ft @ 68 F
Electrical Conductivity 26 %IACS @ 68 F
Thermal Conductivity 67 Btu · ft/(hr · ft2·oF)at 68F
Modulas of Elasticity in Tension 14000 ksi

Brass Plate Application Industries

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Brass Plate Test Certificates

We are provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

ASTM / ASME SB 62 Brass Plate Value Added Services

Material Testing:
We are ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and MacroTest
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Category:

SHOPPING CART

close